O
Orclever
Back to Journal
Research Article Open AccessOrclever Native

Effect of Amorphous Silica–Forming Additive on Porosity and Mechanical Strength in Autoclaved Aerated Concrete Thermal Insulation Board

Yunus Ion Grecu1✉,
Ezgi Biçer2,
Emre Fenerci3,
Ebru Erdoğan4,
Fatma Bakır5
1R&D Center,Nuh Yapı Ürünleri A.Ş., Kocaeli, Türkiye
2R&D Center,Nuh Yapı Ürünleri A.Ş., Kocaeli, Türkiye
3R&D Center,Nuh Yapı Ürünleri A.Ş., Kocaeli, Türkiye
4R&D Center,Nuh Yapı Ürünleri A.Ş., Kocaeli, Türkiye
5R&D Center,Nuh Yapı Ürünleri A.Ş., Kocaeli, Türkiye
Published:December 12, 2025
DOI: 10.56038/ejrnd.v5i1.657
Vol. 5, No. 1

Abstract

Autoclaved aerated concrete (AAC) thermal insulation board has a density of 130–155 kg/m³, a compressive strength above 0.4 MPa and a thermal conductivity value of 0.045 W/m.K. It is a Class A non-combustible, mineral-based and non-toxic material and used for thermal insulation from the outside, inside, in the middle, underground, on floors, and roof surfaces. The porous structure of the material decisively affects its mechanical and thermal conductivity properties. In this study, the potential for pore size reduction was evaluated by adding ratios of 0%, 0.1%, 0.25%, 0.5%, 0.75% and 1% amorphous silica-forming additive to the AAC thermal insulation board by mass. Furthermore, the mechanical performance was compared with the corresponding pore size characteristics. In determining the pore distribution, the air pores in the structure were examined by image analysis technique based on the Monte Carlo approach. When the density and compressive strength of the samples obtained after hydrothermal curing were compared with the A value, it was observed that the highest increase was 29.94% with a 1% additive rate. Scanning electron microscope (SEM) and X-ray diffraction (XRD) analyses showed that the amount of tobermorite increased continuously up to a dosage of 0.5%. The fact that the addition of the admixture by mass reduces the pore diameter, reduces density and increases compressive strength reveals that the amorphous silica-forming additive is usable in AAC thermal insulation board. Achieving the same compressive strength with less material during the production phase and reducing per-unit energy consumption during service due to improved thermal insulation associated with smaller pore sizes are critical for lowering the carbon footprint.

Keywords
Autoclaved aerated concreteThermal insulation boardChemical agentTobermoriteMonte Carlo method

References

  1. 1.Özgür, Y., Özkan Ş., Haluk, Ş., Osman, Ç., Demet, Ö., Şükrü, E. & İlkay, K. (2015). Binalarda ısı yalıtımı ve ısı yalıtım malzemeleri, IMO Yapı Malzemeleri Komisyonu, 60, 62-73.
  2. 2.Bayraktar, D. & Bayraktar E. A. (2016). Mevcut binalarda ısı yalıtım uygulamalarının değerlendirilmesi, Mehmet Akif Ersoy Üniversitesi Fen Bilimleri Dergisi, 7, 59-66.
  3. 3.Bektaş, V., Çerçevik, A. E. & Yerel Kandemir, S. (2017). Binalarda ısı yalıtımının önemi ve ısı yalıtım malzemesi kalınlığının yalıtıma etkisi, Bilecik Şeyh Edebali Üniversitesi Fen Bilimleri Dergisi, 4, 36-42.
  4. 4.Zhao, J., Grunewald, J., Ruisinger, U. & Feng, S. (2017). Evaluation of capillary-active mineral insulation systems for interior retrofit solution, Building and Environment, 115, 215-227.
  5. 5.Akdemir, Ö., Hacırecepoğlu, A., Andıç Çakır, Ö., Sarıkanat, M., Sever, K. & Seki, Y. (2020). Poliüretanın ısı yalıtım özelliklerinin silika esaslı partiküllerle iyileştirilmesi, Dokuz Eylül Üniversitesi Mühendislik Fakültesi Fen ve Mühendislik Dergisi, 22(64), 147-153.
  6. 6.Jerman, M. & Cerny, R. (2012). Effect of moisture content on heat and moisture transport and storage properties of thermal insulation materials, Energy and Buildings, 59, 39-46.
  7. 7.Kotan, T., Fırat, I, Kaya, M. & Ulusu, I. (2018). Binalarda kullanılan farklı ısı yalıtım malzemelerinin ısı iletkenlik katsayılarının Erzincan ili şartlarında termokupl ve termal kamera ile incelenmesi, Uludağ Üniversitesi Mühendislik Fakültesi Dergisi, 23(2), 367-382.
  8. 8.Gören, B. (2022). Gazbeton ısı yalıtım levhasının taş yünü ısı yalıtım malzemesi ile karşılaştırılarak bina enerji performansı ve ısınma maliyetine etkisinin incelenmesi, İstanbul Arel Üniversitesi, Lisansüstü Eğitim Enstitüsü.
  9. 9.Karadayı, T. T. & Yüksek, I. (2016). Yapılarda ısı yalıtım malzemeleri seçimi üzerine bir araştırma, Tesisat Dergisi, 242, 90-102.
  10. 10.Arslan, A. M. & Aktaş, M. (2018). İnşaat sektöründe kullanılan yalıtım malzemelerinin ısı ve ses yalıtımı açısından değerlendirilmesi, Journal of Polytechnic, 21(2), 299-320.
  11. 11.Kreft, O., Straube, B. & Torsten, S. (2011). Internal thermal insulation with light weight autoclaved aerated concrete, In Proceedings of the International Autoclaved Aerated Concrete Conference, Bydgoszcz.
  12. 12.Miccoli, L., Fontana, P., Silva, N., Kocadag, R., Cederqvist, C., Kreft, O. & Ovaeschning, D. (2016). UHPC-AAC/CLC composite panels with self-cleaning properties, Materials and Production Technology.
  13. 13.Majerek, D., Sedzielewska, E., Pasnikowska-Lukaszuk, M., Lazuka, E., Suchorab, Z. & Lagod, G. (2024). Automatic image analysis method as a tool to evaluate the anisotropy of autoclaved aerated concrete for moisture and heat transport, 17, 4903.
  14. 14.Chen, J., Huang, Y., Lie, G., Chen, H., Liang, Y., Rashad, A. M., Lie, J., Zhang, J. & Wang, W. (2025). Performance regulation of ultra-lightweight autoclaved aerated concrete by metakaolin and its impact on energy efficiency in thermal insulation walls, Energy and Buildings, 348, 116374.
  15. 15.Galvankova, L., Masilko, J., Solny, T. & Stepankova, E. (2016). Tobermorite synthesis under hydrothermal conditions, Procedia Engineering, 151, 100-107.
  16. 16.Cerny, V. & Drochytka, R. (2019). The influence of different types of siliceous raw materials on tobermorite formation in lime-silica composite, WSEAS transactions on environment and development, 15, 57-64.
  17. 17.Kreft, O., Hausmann, J., Hubalkova, J., Aneziris, C. G., Straube, B. & Schoch, T. (2011). Pore size distribution effects on the thermal conductivity of light weight autoclaved aerated concrete, 49(52).
  18. 18.Hust’avova, J., Cerny, V. & Drochytka, R. (2020). Monitoring the effect of quartz-sand replacement by amorphous-silica raw material on the microstructure of calcium silicate composites, Materials and Technologies, 54(1), 129-134.
  19. 19.Shams, T., Schober, G., Heinz, D. & Seifert, S. (2021). Production of autoclaved aerated concrete with silica raw materials of a higher solubility than quarts part II: Influence of autoclaving temperature, Construction and Building Materials, 287, 123072.
  20. 20.Shams, T., Schober, G., Heinz, D. & Seifert, S. (2022). Rice husk ash as a silica source for the production of autoclaved aerated concrete – A chance to save energy and primary resources, Journal of Building Engineering, 47, 104810.
  21. 21.Corro-Escorcia, I. A., Hernandez-Avila, J., Cerecedo-Saenz, E. Barrientos-Hernandez, F. R., Cruz-Hernandez, M., Toro, N., Galvez, E., Gutierrez-Amador, M. P. & Salinas-Rodriguez, E. (2025). Synthesis of tobermorite 11 A during the formation of autoclaved aerated concrete with the addition of diatomite, Results in Materials, 26, 100725.
  22. 22.Chen, G., Li, F., Geng, J., Jing, P. & Si, Z. (2021). Identification, generation of autoclaved aerated concrete pore structure and simulation of its influence on thermal conductivity, Construction and Building Materials, 291, 123572.
  23. 23.Uluer, O., Karaağaç, I., Aktaş, M., Durmuş, G., Ağbulut, Ü., Khanları, A. & Çelik, D. N. (2018). Genleştirilmiş perlitin ısı yalıtım teknolojilerinde kullanılabilirliğinin incelenmesi, Pamukkale Üniversitesi Mühendislik Bilimleri Dergisi, 24(1), 24-32.
Download PDF
Cite This Article
Grecu, Y. I., Biçer, E., Fenerci, E., Erdoğan, E., Bakır, F. (2025). Effect of Amorphous Silica–Forming Additive on Porosity and Mechanical Strength in Autoclaved Aerated Concrete Thermal Insulation Board. *The European Journal of Research and Development*, 5(1), 449–464. https://doi.org/10.56038/ejrnd.v5i1.657

Bibliographic Info

JournalThe European Journal of Research and Development
Volume5
Issue1
Pages449–464
PublishedDecember 12, 2025
eISSN2822-2296