O
Orclever
Back to Journal
Research Article Open AccessOrclever Native

Investigation of Wear Behavior of PET Bushings for Turbine Components

Ezgi Özgünerge Falay1✉,
Öz Erman Arusan2,
Rüçhan Yıldız3,
İsmail Ovalı4,
Engin Tan5
1ARNES Mechanical Machinery Design Center
2ARNES Mechanical Machinery Design Center
3Pamukkale University
4Pamukkale University
5Pamukkale University
Published:December 31, 2024
DOI: 10.56038/ejrnd.v4i4.596
Vol. 4, No. 4

Abstract

In this study, for the first time, a new generation PET (Polyethylene terephthalate) material bushing design and prototype production by machining was carried out for the turbine blade and adjustment cap blade used in turbine systems within the Arnes Mechanical Machinery Design Center. Within the scope of the study, the tribological properties of the PET material used as the bushing raw material were investigated under different sliding speeds, loads, and sliding distances. Abrasive wear tests were applied using the pin-on-disc method at 3 and 4.5 m/s sliding speeds, 100-, 200-, and 300-meters sliding distances, and 5, 10, 15, and 40 N loads. The wear performance of the PET material was evaluated through the parameters of volume loss, coefficient of friction, and surface roughness. The results obtained showed that the applied load and sliding speed had a significant effect on the wear behavior of the material. The increase in load caused a significant increase in volume loss by creating a higher contact pressure on the material. This situation showed that higher loads create more contact pressure on the surface, causing deformation and material loss in the material's microstructure. It was evaluated that plastic deformation and abrasive wear mechanisms are dominant on the material surface under high loads. In contrast, increasing the sliding speed caused a decrease in the coefficient of friction and surface roughness. It was observed that at higher speeds, the thermal effects caused by friction on the material's surface resulted in the formation of a tribofilm, thus increasing the surface protection capacity of the material and decreasing the coefficient of friction and surface roughness. The findings showed that the bushings manufactured from PET material can be successfully used as an alternative to metal alloy bushings under difficult service conditions in turbine systems.

Keywords
Turbine BladeAdjustment Cap BladePET BushingWearSurface Roughness

References

  1. 1.Villagran, Y., Gomez, L. H. H., Ortiz, M. P. & Beltrán-Fernández, J. A. (2019). Analysis of the wear damage on offshore gas turbine blades. In book: Engineering Design Applications, 221-236.
  2. 2.Schlobohm, J., Bruchwald, O., Frackowiak, W. & Li, Y. (2016). Turbine blade wear and damage – An overview of advanced characterization techniques. Materials Testing, 58(5), 389-394.
  3. 3.Chen, H., Pan, J., Wang, S., Ma, J. & Zhang, W. (2024). Fatigue damage assessment of turbine runner blades considering sediment wear. Applied Sciences, 14(11), 4660.
  4. 4.Czerniec, M., Czerniec, J. & Zubrzycki, J. (2024). Mathematical modeling of load capacity and durability of metal-polymeric bearings with a composite bushing based on polyamides, polytetrafluoroethylenes, polyetheretherketones, or polyethylene terephthalates. Applied Sciences, 14(23), 11275.
  5. 5.Antwi-Afari, M. F., Mi, H. Y. & Liu, C. (2023). Research on the feasibility of polyethylene terephthalate foam used in wind turbine blades. Enviromental Progress & Sustainable Energy, 42(1), e13956.
  6. 6.Walczak, M. & Caban, J. (2021). Tribological characteristics of polymer materials used for slide bearings. Open Engineering, 11(1), 624-629.
  7. 7.Guan, M., Jin, H., Wei, W. & Yan, M. (2023). Degradation of polyethylene terephthalate (PET) and polypropylene (PP) plastics in seawater. DeCarbon, 1, 100006.
  8. 8.Goujon, N., Demarteau, J., Lopez de Pariza, X., Casado, N., Sardon, H. & Mecerreyes, D. (2021). Chemical upcycling of PET waste towards terephthalate redox nanoparticles for energy storage. Sustainable Chemistry, 2(4), 610-621.
  9. 9.Duan, C., Wang, Z., Zhou, B. & Yao, X. (2024). Global polyethylene terephthalate (PET) plastic supply chain resource metabolism efficiency and carbon emissions co-reduction strategies. Sustainability, 16(10), 3926.
  10. 10.Sarda, P., Hanan, J. C., Lawrence, J. G. & Allahkarami, M. (2021). Sustainability performance of polyethylene terephthalate, clarifying challenges and opportunities. Journal of Polymer Science, 60(1), 7-31.
  11. 11.Zhang, J., Darwish, N., Coote, M. L. & Ciampi, S. (2020). Static electrification of plastics under friction: The position of engineering-grade polyethylene terephthalate in the triboelectric series. Advanced Engineering Materials, 22 (3), 1901201.
  12. 12.Gutnikov, V.A., Kaykazsky V. I. & Usanova K.I. (2024). High performance polymer Zedex-100K based on polyethylene terephthalate: physical, mechanical and operational properties. AlfaBuild, 30, 3005.
  13. 13.Domitran, Z., Zezelj, D. & Katana, B. (2016). Influence of contact pressure and sliding speed on the temperature and coefficient of friction in sliding contact between two PET samples. Tehnički Vjesnik 23(2), 389-396.
  14. 14.ASTM G99-17. (2017). Standard test method for wear testing with a pin-on-disk apparatus, ASTM International, West Conshohocken, PA.
  15. 15.Ovalı, İ. (2017). Abrasive wear behavior of various reinforced AA6061 matrix composites produced with hot pressing process: A comparative study. Materialwissenschaft und Werkstofftechnik, 48(6), 589–599.
  16. 16.Sukumaran, J., De Pauw, J., Neis, P. D., Tóth, L. F. & De Baets, P. (2017). Revisiting polymer tribology for heavy duty application. Wear, 376-377, Part B, 1321-1332.
  17. 17.Tóth, L. F., Sukumaran, J., Szebényi, G. & De Baets, P. (2019). Tribo-mechanical interpretation for advanced thermoplastics and the effects of wear-induced crystallization. Wear, 440-441, 203083.
  18. 18.Cho, D. H., Bhushan, B. & Dyess, J. (2016). Mechanisms of static and kinetic friction of polypropylene, polyethylene terephthalate, and high-density polyethylene pairs during sliding. Tribology International, 94, 165-175.
  19. 19.Bhushan, B., & Ko, P. L. (2003). Introduction to tribology. Applied Mechanics Reviews, 56(1), B6-B7.
  20. 20.Myshkin, N. K., Petrokovets, M. I., & Kovalev, A. V. (2005). Tribology of polymers: Adhesion, friction, wear, and mass-transfer. Tribology International, 38(11-12), 910-921.
Download PDF
Cite This Article
Falay, E. Ö., Arusan, Ö. E., Yıldız, R., Ovalı, İ., Tan, E. (2024). Investigation of Wear Behavior of PET Bushings for Turbine Components. *The European Journal of Research and Development*, 4(4), 316-327. https://doi.org/10.56038/ejrnd.v4i4.596

Bibliographic Info

JournalThe European Journal of Research and Development
Volume4
Issue4
Pages316–327
PublishedDecember 31, 2024
eISSN2822-2296